Overview

Widely chosen by customers for its reliability and accuracy, the vortex flow meter also serves as a standard for steam applications due to its ease of installation and low maintenance costs. Where other meter technologies struggle in difficult high-pressure and high-temperature environments, the vortex flow meter offers a wide range and a low pressure drop, making it a top choice for flow professionals.

Vortex meters from Panametrics, a Baker Hughes business, include both inline and insertion modes, providing ease of installation for demanding applications, including:  

  • Hot-tap steam
  • Large lines
  • Areas of low pressure

Our PanaFlow vortex meter offers a multivariable design that contains shedding velocity with RTD temperature sensors and a solid-state pressure transducer for measuring mass flow rate of steam, gases and liquids. The accuracy of these meters enables velocity, temperature and pressure to be measured at the same location.

Vortex Product Features
MV84 Vortex Flow Meter

The PanaFlow MV80 is a cost effective and accurate inline vortex flow meter that saves you time and costs by measuring flow, temperature, pressure, density, energy and mass in a single meter, with no need to recalibrate for most gases, liquids and steam.

MV84
MV82 Vortex Flow Meter

The PanaFlow MV82 insertion mass flow meter is a multivariable vortex flow meter for measuring volumetric flow, temperature, pressure, density and mass flow. It offers an advanced design and digital signal processing to isolate vibration. This meter is accurate, reliable and cost effective for measuring any process flow.

MV82
FAQ about Vortex Flowmeters
Geothermal application

Do the Panametrics Vortex meters work in geothermal steam mass flow measurement?

Can they measure steam line containing steam, condensed water and some hydrocarbon gases mix?

 

Yes, they can measure flow in geothermal steam applications. The vortex meter only measures steam in the gas phase and will not measure the condensate. Due to the corrosive nature of the hydrocarbon gas and other impurities that we experienced, we provided Hastelloy C meters which matched up to the application's piping.  

Pressure and temperature data

Can the pressure and temperature data be sent back to the control room?

Yes, the pressure and temperature can be sent back to the control room with any of the digital communication options (HART, Modbus, or BACnet).

Available insertion lengths for the vortex flowmeters
Image
Vortext insertion formula

What are the available insertion lengths for the vortex meters? 

If using the standard nozzles and valves, the typical recommendation is:

  • Compression probe seal -> compact length
  • Packing gland seal -> standard length

If a custom nozzle or valve is required, please review the manual for stem length and recommendation between a compact, standard, and extended length.

See example for a compression installation from the manual.

Are there special power requirements for BACnet protocol?

Are there special power requirements for BACnet protocol?

The vortex meters have the following power options.

  • DC2: 12-36VDC (2 Wire Loop – Use 1AHL Only)
  • DC4POE:  12-28VDC or Power over Ethernet (5Watts max.), TCP/IP option only
  • DC4: 12-36VDC (4 Wire)
  • AC: 100-240 VAC, 50/60Hz

For BACnet, you can not use the loop power option.

For BACNet/MSTP, select either DC4 or AC power.

For BACNet/TCPIP, select DC4POE or AC.

Background vibrations & noise

Do vortex meters account for the background vibrations & noise?

 

The vortex meters by design and signal processing do take into consider background vibration and noise. 

Two sensors are installed in each velocity tag to prevent common cause noise such as background vibration.  Also, based on programming, the meter isolates the expected signal location to focuses on the true vortices frequency.

Is there any chance for pressure drop in Vortex?

Is there any chance for pressure drop in Vortex?

Yes, the vortex meter will cause a pressure drop and the amount is detailed in the vortex sizing program.

Using a reducing flange effect to the accuracy

How does using a reducing flange effect the accuracy and the upstream piping for a vortex meter?

The same accuracy and upstream piping conditions apply.

What is the upstream and downstream requirements?
Image
Oil and gas application vortex

What is the upstream and downstream requirements?

  • Liquid: 10D upstream and 5D downstream
  • Gas: 20D upstream and 10D downstream
  • Assumes simple disturbance… see chart and manual for details.
Learn about Panametrics' Industry Solutions
Refinery Solutions

Discover next generation solutions for minimal risk and maximum performance

Refineries and petrochemical plants
Water and wastewater Solutions

Panametrics’ experience and solutions in water and wastewater

Water and wastewater Panametrics
Food and Beverage Solutions

Measure liquid flow Non-Intrusively and Non-Invasively

Food and Beverage Solutions Panametrics
Steel Solutions

Panametrics’ experience and solutions in Steel Industry

Steel Solutions from Panametrics

Get in touch with an expert.

Your request has been submitted.
Thank you for your interest. A specialist will be in touch with you shortly.